consultingferro.blogg.se - Black talon grips for glock 43

#BLACK TALON GRIPS FOR GLOCK 43 INSTALL#
#BLACK TALON GRIPS FOR GLOCK 43 SKIN#
#BLACK TALON GRIPS FOR GLOCK 43 FULL#
#BLACK TALON GRIPS FOR GLOCK 43 PROFESSIONAL#

ANY TIME YOU ARE USING A DREMEL ON A POLYMER FRAME YOU SHOULD USE THE LOWEST SPEED ON YOUR DREMEL. I think if you dont do this it looks like crap and is amateur hour. If you dont do this you will see the difference in height from the raised texture to the flat smooth parts. The next step is to sand off all the texture that is from the factory with your dremel.

#BLACK TALON GRIPS FOR GLOCK 43 PROFESSIONAL#

You dont need to do this but the more I do these, the more I think it’s easier and looks more professional if you pull all the lower parts and pull the mag release. Then clean the polymer with the alcohol.

compressed air – could be a can of keyboard dusterįield strip the pistol and disassemble the lower portion of the pistol.

I touched on it a little in the 26L write up but this will be more detailed around stippling in general. This would be the same process for any polymer pistol.

So the purpose of this post is just to walk you through how I did the stippling and to answer any questions people have. I have been wondering how well cerakoted does on pistols with holster wear so I said what the hell.Īll this of course was pretexted on the fact that I would have to get the stippling done too my liking before he cerakoted it. I thought that might be interesting and since he already had the paint mixed up it would be easy to do. When he saw I got the 43 he said we should cerakoted it. He mixed up extra paint and set it off to the side as he liked the color. We spent a while trying to find a good color and we ended up doing a custom color of 25% Burnt Bronze and 75% FDE.

#BLACK TALON GRIPS FOR GLOCK 43 FULL#

I will do a full write up at some point.Īnyways, I have a great gunsmith locally and he offered to cerakote it and then he would built out the rifle. I purchased a colt lower parts kit from G&R Tactical and other than the grip which was an Umbrella Corp the rest of the gun was BCM parts including the 11.5 BCM upper. I just needed to find the time to do the work.Ībout 6 months ago I picked up an Umbrella Corp AR lower and decided to build out a 556 SBR. So I decided that a stippling job was in order. They work and are much better than stock but I have grown spoiled with the stippling on my 19s and 26L. So when I got the 43, I put about 300 round downrange before deciding to throw on the talon grips. If you are not wearing an undergarment it can rub you the wrong way. I generally go with the rubber because the sandpaper seems to bug me while I am carrying concealed. You can get them in a sandpaper (like skateboard tape) or in a rubber grip tape. Talon grips, if you are not familiar with them, are an affordable, easy to put on grip tape that is customized for your pistol. As I knew I would have 43 soon I went ahead and ordered a set of Talon Grips that I have used before and worked well on my Nano. The pistol is not hard to shoot but you can tell right off the bat that it would benefit from a better texture. I think GLOCK was thinking low drag or less texture to run up against you when using the pistol for concealed carrying.

Adhesive will not move once properly installed and can be easily removed with little to no residue.The GLOCK 43 surprisingly has a very light texture.

Most cleaning solutions do not harm the grip, but avoid aerosol based solvents like CLP.

#BLACK TALON GRIPS FOR GLOCK 43 INSTALL#

Easy to install within minutes (proper installation requires a hair dryer or heat gun).

#BLACK TALON GRIPS FOR GLOCK 43 SKIN#

Available in rubber texture – This textured rubber grip provides positive grip on the firearm and is more commonly used for concealed carry (less likely to irritate skin or snag on clothing) and users with softer hands.

Available in granulate texture – Often referred to as sandpaper or skateboard tape, this provides positive grip on the firearm and best suited for holster carry and competition shooting.

Low profile grip adds minimal bulk/size.

Custom designed and manufactured for this specific firearm for an OEM quality fit and finish.

This grip includes the graphic “GLOCK” cutout on the shooter’s left and the TALON “T” on the shooter’s right as well as relief cuts for the thumb rest on each side. This grip has full coverage on the side panels including above the thumb rest, high coverage on the backstrap, and full coverage under the trigger guard. This rear wrap grip is available in both granulate and rubber textures.